Barco E-2320 C (SE) Informacje Techniczne

System ManualE-2320 C (SE)

Preface10Canadian noticeThis Class A digital apparatus complies with Canadian ICES-003.Cet appareil numérique de la Classe A est conforme à la norme N

Warranty Statement100(This page intentionally left blank)

Warranty Statement101ARTICLE 1: SERVICESBarco n.v. warrants that the equipment will be free of defects in workmanship or material for the warranty per

Warranty Statement102this paragraph shall excuse Barco's performance hereunder:3.1 Customer shall not expose Barco personnel to any unsafe workin

Warranty Statement103(This page intentionally left blank)

www.barco.comK5904185-00October 2007

Preface11• Consult the dealer or an experienced radio/TV technician for help. The use of shielded cables for connection of the monitor to the graphics

Environmental information12Environmental informationDisposal InformationThis product consists of devices that may contain mercury, which must be recyc

Environmental information13Information for China ROHS complianceTable of toxic and hazardous substances/elements and their content, as required by Chi

Environmental information14

Safety Instructions15Safety InstructionsGeneral RecommendationsRead the safety and operating instructions before operating the display. Retain safety

Safety Instructions16Power cord with CEE 7 plug: The colors of the mains lead are colored in accordance with the following code: Green-and-yellow: Ear

Safety Instructions17Operating precautionsContinuous operation of the display with the same image may result in some image sticking on the LCD panel.

Explanation of symbols18Explanation of symbolsSymbols on the display and / or power supplyOn the display or power supply, you may find the following s

Explanation of symbols19Symbols used throughout the manual:Warning CautionImportant notice or remarkNoteHint, tip Additional information

2(This page intentionally left blank)

Explanation of symbols20(This page intentionally left blank)

21Introduction

Introduction22(This page intentionally left blank)

Overview23OverviewThank you for choosing Barco.Single display or complete system?This manual describes installation and usage of the display only. How

Overview24Power savingThe display is equipped with a power saving system. When left idle for a certain time, the computer connected to the display, wi

Package contents25Package contentsSystem packageIn case you have purchased a complete system, the system contains one or more display boxes (see below

Parts, controls and connectors26Parts, controls and connectorsFrontFigure 11. Control wheelThe control wheel can be pressed like a push button and rot

Parts, controls and connectors27RearFigure 21. Connector compartment coverTo get access to the connectors, remove the cover by pulling down the 2 clip

Parts, controls and connectors287. USB upstream portUSB 1.1 standard is supported.Connect this connector to the PC USB bus if you wish to connect USB

29Installation

3Copyright noticeThis document is copyrighted. All rights are reserved. Neither this document, nor any part of it, may be reproduced or copied in an

Installation30(This page intentionally left blank)

Installation precautions31Installation precautionsPrecautions• Keep your original packaging. It is designed for this display and is the ideal protecti

Installing your Barco display controller32Installing your Barco display controllerThis chapter will guide you through the physical installation of the

Installing your Barco display controller33Figure 3: BARCOMED CORONIS PCIe display controller VGA Jumper, VGA enabledNote: To use multiple BARCOMED COR

Installing your Barco display controller34To perform a quick installation1. If you are not going to use your old graphics card, uninstall the drivers

Installing your Barco display controller353. Unplug the computer’s power cord and disconnect all cables from the back of your computer.4. Remove the c

Installing your Barco display controller36Figure 5: Power connection for the MXRT 5100 and 7100 controllers9. Screw in or fasten the display controlle

Installing your Barco display controller37Figure 7: 11. Reconnect any cables you have disconnected and plug in the computer’s power cord.12. Turn on t

Installing your Barco display controller38If you have properly installed your graphics card, the Windows start-up messages will appear once the boot p

Display installation39Display installationAfter unpacking the displayImportant:In the factory, the height-positioning system in the display foot is bl

4(This page intentionally left blank)

Display installation40To change the panel orientation:1. Stand at the front side of the panel and take the panel at both sides.2. Very important: Tilt

Display installation41Figure 104. To change from portrait to landscape, turn the panel counterclockwise.Power connectionTo connect the power:1. To get

Display installation42Figure 113. Connect one end of the proper power cable to the AC input of the 12V DC power supply.Figure 124. Connect the other e

Display installation43Video connectionThe display has 2 different video inputs: Digital (DVI) and VGA (Sub-D 15).You can connect one or more of these

Display installation44Connecting analog videoProceed as follows:1. Connect one end of the VGA cable to the D15 input of the display.2. Connect the oth

Display installation45To connect the USB cable:1. Connect the display’s USB upstream connector to the USB port of the PC by means of a USB cable.2. Co

Display installation46To put the foot cover in place:Figure 16: 1. The foot cover is packaged separately in the accessory box. Unpack the foot cover.2

Attaching the display to an arm47Attaching the display to an armThe panel, standard attached to the tilt & swivel foot, is compatible with the VES

Attaching the display to an arm484. Unscrew the 2 screws fixing the round plastic cover (B).5. Lift up the round plastic cover.6. Remove the four scre

Installing drivers and software49Installing drivers and softwareThis chapter will guide you through the installation of the drivers, software and docu

Table of Contents5Table of ContentsPreface... 7Environmental informa

Installing drivers and software50• Windows Server 2003 x64 Edition.You will need to install the BARCO E-2320 C Display system drivers and software in

Installing drivers and software515. Follow the wizard’s on-screen instructions to complete the installation.Note: There are two options for installing

Installing drivers and software527. When the Setup complete message appears, select Reboot System Now and click Finish.8. After the system reboots, Wi

Installing drivers and software53Figure 19: Barco Driver Removal WizardCommand line (Silent) Install of Drivers and SoftwareSpecifying the silent inst

Installing drivers and software54ora) browse to the root directory of the location where you saved the contents of your BARCO NIO Display System Insta

55Operation

Operation56(This page intentionally left blank)

BARCO MXRT control panel settings57BARCO MXRT control panel settingsThis chapter describes how to configure the displays in your BARCO NIO Display Sys

BARCO MXRT control panel settings58graphics controller advanced configuration pages. The second section provides information about the display. The bo

BARCO MXRT control panel settings59MediCal QAWebClicking on the MediCal QAWeb button will launch the MediCal QAWeb application. Please refer to the Me

Table of Contents6On-screen display ... 66Using the Autoset function ...

BARCO MXRT control panel settings60Custom SettingsNote: Barco recommends that you use the default settings, unless your viewing application vendor pro

BARCO MXRT control panel settings61Texture preferenceThis slider enables you to select the texture quality level.• Maximize overall performance by mov

BARCO MXRT control panel settings62• Diagnostic purposes.• Fine-tuning a specific application/system configuration.• Specific settings recommended by

BARCO MXRT control panel settings63configuration controls on this tabbed dialog to obtain the desired display parameters for the selected application.

BARCO MXRT control panel settings64Configuring the Windows desktopNote: If you are using a color display in conjunction with your Barco grayscale disp

Display operation65Display operationOperating precautionsContinuous operation of the display with the same image may result in some image sticking on

Display operation66On-screen displayAbout the on-screen displayThe on-screen display (OSD) has a hierarchical structure, with several levels. The top

Display operation672. To enter into a menu or move to a lower level of the menu structure, rotate the control wheel to select the desired menu. Next,

Display operation68• The image should contain sharp black-white transitions, like a line pattern or characters.• The image should contain parts that a

Display operation69You can perform the following adjustments:* Not available in DVI modeContrast adjustmentThis adjustment is not necessary (and not a

7Preface

Display operation703. Press the control wheel to enter the Video Contrast menu.4. Rotate the control wheel to select Man Contrast adj.5. Press the con

Display operation713. Press the control wheel to enter the Video Brightness menu.4. Rotate the control wheel to select Man Brightness adj.5. Press the

Display operation725. Press the control wheel to enter the Color Temp Definition menu.6. Rotate the control wheel to select the color temperature you

Display operation73To enable user controls:1. Do not use the control wheel for at least 3 seconds.2. Rotate the control wheel 1 step clockwise.3. Pres

Display operation74Complete OSD overviewMain menuName Description Presentin DVI modeAutoset Allows to perform automatic image adjustmentsNoVideo Contr

Display operation75AutosetThe Autoset menu is not available in DVI mode.When do you need to use the Autoset function?• The first time you use the disp

Display operation76Required test patternTo obtain good results with the autoset functions, it is necessary to have a good image on which to perform th

Display operation77Caution: Increasing the luminance setting to a value higher than 100% may significantly decrease the lifetime of the display backli

Display operation78Adjustments: PhaseThis menu is not available in DVI modeInput Selection Name DescriptionAutomatic Phase This is the same function a

Display operation79SettingsName DescriptionDPMS Switch on/off the automatic power saving system (DPMS)Power LED Switch the power LED on/off. Note: The

Preface8(This page intentionally left blank)

Display operation80Information - General Information:Information - Current Input Format:Name DescriptionProduct The display typeSerial No Indicates th

81Cleaning

Cleaning82(This page intentionally left blank)

Cleaning83Precautions• Take care not to damage or scratch the front filter or LCD panel. Be careful with rings or other jewelry that can touch the fro

Cleaning84Attention: The dust remover contains a liquid gas. If you shake the can or move the can too fast while spraying, you may blow drops of liqui

85Troubleshooting

Troubleshooting86(This page intentionally left blank)

Troubleshooting87General tips• If one display from a multi-head system exhibits problems, try to eliminate the problem by switching video cables or po

Troubleshooting88Problems and solutionsProblem description Possible tests or solutionsScreen remains black • Please check the installation procedure i

Troubleshooting89The PC does not start up • Check the CMOS settings in the PC BIOS• The display controller may not be firmly seated in the connectorNo

Preface9NoticeAlthough every attempt has been made to achieve technical accuracy in this document, we assume no responsibility for errors that may be

Troubleshooting90Note: What if the graphic board resolution is too lowSome non-Barco graphic boards (e.g., single-link boards) may have an insuffician

91Technical Information

Technical Information92(This page intentionally left blank)

Technical specifications93Technical specificationsE- 2320 C (SE):Item SpecificationPicture panel 20.1-inch diagonal viewable screen TFT (thin film tra

Technical specifications94Input signals Possible resolutions:• 640 x 480 @ 60, 75, 85, 100 Hz• 800 x 600 @ 60, 75, 85, 100 Hz• 1024 x 768 @ 60, 75, 85

Connector pin assignments95Connector pin assignmentsDVI connector:Figure 23: DVI connector pin layoutPin no. Signal Pin no. Signal1TMDS DATA 2- 14+5V

Connector pin assignments96D-Sub 15 connector (analog video):Figure 24: D-Sub 15 pin layoutPin no. Signal Pin no. Signal1Red in 9DDC 5V IN2 Green in 1

Glossary97GlossaryCalibrationEach display is calibrated in the factory before it is sent to the customer. After this calibration, black and white lumi

Glossary98DICOMDICOM stands for Digital Imaging and Communications in Medicine. It is a standard developed by the American College of Radiology (ACR)

99Warranty Statement