Barco Coronis 3MP Instrukcja Użytkownika

Installation & User ManualCoronis 3MP

10Display Operation ... 51Operation ...

11Display Controller Installation

Display Controller Installation12(This page intentionally left blank.)

BarcoMed CORONIS display controller overview13BarcoMed CORONIS display controller overviewThe BarcoMed CORONIS display controller delivers a quality i

BarcoMed CORONIS display controller overview14Supported resolutions for each head of the BarcoMed CORONIS display controllerFor Coronis 3MP Displays•

BarcoMed CORONIS display controller installation15BarcoMed CORONIS display controller installationCaution: Wear a grounded, protective ESD strap durin

BarcoMed CORONIS display controller installation16Figure 2: VGA Jumper Enlarged ViewUsing the VGA capabilities of the BarcoMed CORONISPrior to install

BarcoMed CORONIS display controller installation17Figure 3: PCI and RAID Controller SlotsInstall the BarcoMed CORONIS controller in your computer foll

BarcoMed CORONIS display controller installation18below) using the provided DVI cable. For a dual-headed BarcoMed CORONIS setup, connect the secondar

19Display Installation

2 Coronis 3MP(This page intentionally left blank.)

Display Installation20(This page intentionally left blank.)

Overview21OverviewIntroductionThe MFGD 3420, BARCO’s 20” 3 megapixel grayscale LCD display, guarantees perfect image quality in medical imaging appli

Overview22Power saving (DPMS)The MFGD 3420 is equipped with a power saving system. When left idle for a certain time, the computer connected to the di

Overview23Controls and connectorsFigure 5Front(1) Power LED• The LED is off when the display is off.• The LED is green when the display is on (when en

Overview24Figure 6Side(2) USB downstream connector(3) Control wheel for navigating through the on-screen display (OSD) menus and changing values in th

Installation25InstallationPrecautions• Keep your original packaging. It is designed for this display and is the ideal protection during transport.• Av

Installation26To remove the clip:1. Position the display with its rear side facing you.2. Lift up the 2 clips of the foot cover to release the cover f

Installation27Figure 9Should you change the panel orientation without tilting it first, you might irreversibly damage the tilt & swivel mechanism.

Installation28To connect the power:Figure 101. Connect the output of the 12V DC power supply to the DC input (7) of the display.2. Connect one end of

Installation29 Figure 111. Push the upper side of the cover onto the foot, so that the hooks on the cover are positioned right under the holes in t

Copyright notice3Copyright noticeThis document is copyrighted. All rights are reserved. Nor this document, nor any part of it, may be reproduced or

Installation30Tilt and swivel positioningAdjust the position of the panel for best viewing conditions.The display foot allows adjusting the horizontal

How to avoid image retention31How to avoid image retentionImage retention (image sticking, ghost image) is the phenomenon where an image, or a part of

How to avoid image retention32To activate appropriate screen saving, proceed as follows:1. In the display OSD menus, open the Settings menu and switch

33Software Installation

Software Installation34(This page intentionally left blank.)

35Installing the BARCOMED display controller drivers and softwareNote: The installation dialog will display in English if your operating system’s lang

Single Source Master36c) Click Browse and browse to the root directory of the BARCO MEDICAL IMAGING DISPLAY SYSTEM CD-ROM and click on the file, Setup

37Please refer to your application manuals for information on the correct Palette and Drawing modes to select.6. When the driver setup is complete, cl

Single Source Master38un-installed. This is normal, please follow the prompts from the wizard.Command line (Silent) Install of Drivers and SoftwareSpe

39See figure 2 for an example of how the command line window should look when using the silent install from the BARCO MEDICAL IMAGING DISPLAY SYSTEM C

Preface4PrefaceNoticeAlthough every attempt has been made to achieve technical accuracy in this document, we assume no responsibility for errors that

Single Source Master40

41Display Controller Tools

Display Controller Tools42(This page intentionally left blank.)

43BarcoMed Control Panel Settings

Single Source Master(This page intentionally left blank.)44(This page intentionally left blank.)

45BarcoMed control panel settingsThis chapter describes how to configure the displays in your Barco Medical Imaging Display System using the tools ava

BarcoMed control panel settings Single Source Master46installed on your system. Also, there is a active link to the Barco Medical Imaging web site.Fig

47Advanced PropertiesTo access the advanced properties configuration pages for your Barco display controller(s), click on the Advanced button in the G

BarcoMed control panel settings Single Source Master48correctly with 8-bit (256-color) modes should continue to work normally.Note: Ditherng is not us

49Windows graphics device interface (GDI). DirectDraw is enabled by default.More information about DirectDraw is available through the on-line help.En

Preface5Disposal InformationThe lamps inside the display contain mercury. Do not throw the display in the trash. Dispose of it as required by local or

BarcoMed control panel settings Single Source Master50results in increased performance since the frame buffer is set to run with 8-bit pixels. While t

51Display Operation

Display Operation52(This page intentionally left blank.)

Operation53OperationOperating precautionsContinuous operation of the display with the same screen may result in some image sticking on the LCD panel.O

Operation54The Main Menu appears. This is the top level of the menu system.• To browse or scroll through the menus on the current level, turn the whee

Operation55Saving changesWhen you change a value, the change is automatically saved.Setting the Luminance valueWith this function, the backlight value

Operation563. Turn the wheel to select the desired menu item.4. Perform the settings as described below.The Settings menu contains the following items

Operation57To enter the Information menu:1. In the main menu, turn the control wheel to select the Information menu.2. Click the control wheel. The In

Advanced functions58Advanced functionsAbout this chapterImportantThe functions described in this chapter are intended for trained service staff only!I

Advanced functions593. Click and hold the control wheel for a few seconds until the OSD main menu is refreshed on the screen.You have now logged in as

Safety Instructions6Safety InstructionsGeneral RecommendationsRead the safety and operating instructions before operating the display. Retain safety a

Advanced functions60Advanced functions in the Settings menuThe Settings menu contains the following advanced functions:Important: Disabling the I-Guar

Advanced functions61ServiceThe Service information menu contains the following items:FirmwareThe Firmware information menu contains the following item

Advanced functions62MeasurementsThe Measurements info menu contains the following items:Scan MeasurementsThe Scan Measurements info menu contains the

Advanced functions63Advanced functions in the Adjustments menuIn Advanced mode, the main menu contains an additional menu, Adjustments. This menu cont

Maintenance64MaintenancePanelTake care not to damage or scratch the panel. Clean with a soft woolen or cotton towel lightly moistened with plain water

Maintenance653. Unscrew the 4 sunken screws at the rear, fixing the glass panel and bezel.4. Unplug the cable plugged in on the bezel.5. Remove the be

Troubleshooting66TroubleshootingWindows does not show the desired display settingsShould you have problems selecting display settings for portrait ori

Troubleshooting67Pixel FaultsPermanently dark or bright pixels can happen to TFT displays. 20 or less permanently dead pixels do not make out a good

Technical specifications68Technical specificationsPicture panel20.8-inch diagonal viewable screen TFT (thin film transistor) active matrix, greyscale

Technical specifications69Response time25 ms (@ 25° C after 30 min warmup)ControlsPush / turn control wheel for stand-by switching and brightness cont

Safety Instructions7•Power cords:Power cord with CEE 7 plug: The colors of the mains lead are colored in accordance with the following code: Green-and

Technical specifications70Humidity(Relative, non condensing)Operation: 8% - 80%Storage: 5% - 95%Due to our policy of continuous product improvement, t

71MediCal SoftwareInstallation and Operation

MediCal Software Installation and Operation72(This page intentionally left blank.)

MediCal Pro installation and operation73MediCal Pro installation and operationMediCal Pro software installationInstall MediCal Pro on the PC. Follow t

MediCal Pro installation and operation748. Run the due tasks.Please refer to the MediCal Pro User Guide for more information.

75Troubleshooting

Troubleshooting76(This page intentionally left blank.)

77Setting the resolution of your CORONIS 3MP displayNote: In order to set the resolution of your CORONIS 3MP you must be logged in using an account w

Single Source Master78display of the BarcoMed CORONIS display controller you are working with by right clicking on the rectangle that represents it, d

79If you are using a Quad-Head Configuration repeat all of the above steps for the two displays on the second display controller.Note: If you have a

Safety Instructions8This apparatus conforms to:CE, IEC 60950, UL 60950, CAN/CSA C22.2 No. 60950 (c-UL), CCC.National Scandinavian Deviations for Cl. 1

www.barco.comB4100520-02March 2007

9Copyright notice..................... 3Preface ...........